Satisfactory, No change in the height of the cone obtained after 48 hour
Binder Content
19.5 per cent by mass
Luminance Factor
85% (Day light)
Solid Glass Bead Content
31.9 percent by mass
Titanium Oxide
10.3 per cent by mass.
Calcium Carbonate & Inert Fillers
38 percent by mass
Other Details:
Cracking resistance when applied on concrete block Satisfactory, No crack found on the paint when applied on a concrete block and kept it at 0 Deg C for 72 hours.
Heat the material to 180 - 200 °C in the pre-heater with adequate agitation till the material becomes a homogenized liquid. Ensure that the road surface is clean, free from dust and moisture. Heavy deposits of paints requires removal. For aged asphalt roads and concrete road's application of a primer coat is recommended for proper bonding of the material with the road surface ensure that the primer is thoroughly dry and void of solvent prior to application of the thermoplastic material. Do not hold thermoplastic above 180ºC for more than 6 hours do not heat the material above 220ºC at any point in time. The change in colour indicates that the material has been scorched owing to overheating and needs to be discarded. Drop-on glass beads must be immediately deposited after thermoplastic application.
Safety Information:
Minimise dusting of the material during use of personal protective equipment's like facemask, google, heat resistant gloves and protective clothing while handling the material is recommended. do not inhale product or fumes, do not ingest. avoid eye contact, if contacted, wash copiously with water. contact of the molten product with skin would lead to thermal burns, flush with cold water, do not remove material as it would lead to very tissue damage. Please refer the material safety data sheet prior to using the product.
Brightline Thermoplast Private Limited Hot melt Retro Reflective Thermoplastic Road Marking Paint. Thermoplastic is a long life road marking material that was first used in the USA in 1958, followed quickly by its introduction into many countries throughout Europe. It is a mixture of glass beads, binder, pigment and filler material. Thermoplastic can be used very effectively for large anti-skid areas on roads and pedestrian walkways by adding glass beads. It can be produced in any colour and is suitable for car parks, factory walkways, and many other areas. It hardens quickly and can be driven over after just a few minutes. Thermoplastics typically have a service life of 3-5 years, depending on conditions. In winter climates, thermoplastics are very susceptible to snow plows due to its raised structure and can be sheared completely off, leaving no marking on the road. It's highly adhesive. ... It's fast drying. ... It's heat-stable and color-resistant. ... It offers increased resistance to road wear and tear and tropical climate conditions. ... It is the ideal kind of paint for reflectorized traffic paint applications. Thermoplastic road markings vary in thickness between 1.5 mm and 3 mm
Request Callback
Additional Information:
Item Code: WHITE
Production Capacity: 1000MT
Delivery Time: IMMEDIATE
Packaging Details: 25KG
Yes! I am interested
Thermoplastic BS Grade Road Marking Material
Get Best Quote
Approx. Price: Rs 55 / KgGet Latest Price
Product Details:
Minimum Order Quantity
1000 Kg
Color
White
Usage/Application
Pedestrian crossings
Form Of Paint
Powder
Packaging Type
BAG
Softening Point
105
We are a leading organization of the domain, engaged in offering an effective array of Thermoplastic Road Marking Service for customers. These offered road marking services are rendered using modern technology. Apart from this, these road marking services are provided according to the client's desires.
Satisfactory, No change in the height of the cone obtained after 48 hours
Solid glass bead content
31.9 percent by mass
Titanium Oxide
10.3 per cent by mass.
Calcium carbonate & inert fillers
38 percent by mass
Other Details:
Cracking resistance when applied on concrete block Satisfactory, No crack found on the paint when applied on a concrete block and kept it at 0 Deg C for 72 hours.
Satisfactory, No change in the height of the cone obtained after 48 hours
Solid Glass Bead Content
31.9 percent by mass
Titanium Oxide
10.3 per cent by mass.
Calcium Carbonate & Inert Fillers
38 percent by mass
Other Details:
Cracking resistance when applied on concrete block Satisfactory, No crack found on the paint when applied on a concrete block and kept it at 0 Deg C for 72 hours.
Request Callback
Yes! I am interested
Glass Beads Drop On Premium Shine
Get Best Quote
Approx. Price: Rs 95 / KgGet Latest Price
Product Details:
Minimum Order Quantity
500 Kg
Application
Drop On
Shape
ROUND
Bead Size
600–850 µm
Coating Type
Silane Coated
Glass Type
Soda Lime Glass
Reflectivity Grade
Type II
Bulk Density
1.4–1.5 g/cm³
Size
850
Color
TRANSPERENT
Material
CLEAR GLASS
Packaging Type
25
RETRO REFLECTIVE GLASS BEADS:- Product DescriptionGlass beads for road marking can improve the retro-reflection property of the road marking of the line. The driving at night, the headlights shines on the road marking line with glass beads, the light of headlights is reflected back parallelly. So, the driver can see the road ahead clearly, and drive safely at night.Other Details: Protects from Moisture and Water Use no hooks.
Road studs provide effective night guidance during night hours and in adverse weather conditions.
The studs are easily visible and can be heard and felt due to the rumble when a vehicle crosses over them.
3M road studs Designed for application on asphalt and concrete road surfaces, these road studs provide highly effective, long-life visibility, particularly at night and in wet weather.
These road studs are durable, lightweight thermoplastic markers with pressure sensitive adhesive that provide highly effective, long-life visibility, particularly at night and in wet weather.
Road studs provide effective night guidance during night hours and in adverse weather conditions.
The studs are easily visible and can be heard and felt due to the rumble when a vehicle crosses over them.
3M road studs Designed for application on asphalt and concrete road surfaces, these road studs provide highly effective, long-life visibility, particularly at night and in wet weather.
These road studs are durable, lightweight thermoplastic markers with pressure sensitive adhesive that provide highly effective, long-life visibility, particularly at night and in wet weather.
300 Kg (12 Bag) Air Jacketed Easy Operation (Paint Tank Capacity)
Body Material
SS
Engine Type
Diesel/Petrol
Operated Time
8-10 Hour
Heating System
LPG or Diesel Burner Single Pilot Burner as a Torch for Main Burner
Temperature Gauge
One heavy duty gauge to monitor heating process
Agitator
Gear box driving stirrer
Structural Design
Chassis and main frame made of low carbon channels
Power Transmission
Reduction Gear
Dimension
1000 x 1000 x 1200 mm
Direction for use:
Heat the material to 180 - 200 °C in the pre-heater with adequate agitation till the material becomes a homogenized liquid. Ensure that the road surface is clean, free from dust and moisture. Heavy deposits of paints requires removal. For aged asphalt roads and concrete road's application of a primer coat is recommended for proper bonding of the material with the road surface ensure that the primer is thoroughly dry and void of solvent prior to application of the thermoplastic material. Do not hold thermoplastic above 180ºC for more than 6 hours do not heat the material above 220ºC at any point in time. The change in colour indicates that the material has been scorched owing to overheating and needs to be discarded. Drop-on glass beads must be immediately deposited after thermoplastic application.
Safety Information:
Minimise dusting of the material during use of personal protective equipment's like facemask, google, heat resistant gloves and protective clothing while handling the material is recommended. do not inhale product or fumes, do not ingest. avoid eye contact, if contacted, wash copiously with water. contact of the molten product with skin would lead to thermal burns, flush with cold water, do not remove material as it would lead to very tissue damage. Please refer the material safety data sheet prior to using the product.
Our organization is highly popular in offering Zebra Crossing Painting Services to our clients. Experts make use of long lasting paints for this purpose. These are quality services. These are rendered in compliance with requirements of clients. We are offering these Zebra Crossing Painting Services at market leading price. Experts ensure reliability, flexibility and timely execution.
Request Callback
Additional Information:
Item Code: PREMIUM
Production Capacity: 1000MT PER MONTH
Delivery Time: 1 DAY
Packaging Details: 25 kgs
Yes! I am interested
ITraff Water Based Paint
Get Best Quote
Approx. Price: Rs 110 / LitreGet Latest Price
Product Details:
Minimum Order Quantity
20 Litre
Paint type
Water based
Color
White
Packaging size
20 L
Application surface
Concrete road
Reflectivity
Non reflective
Finish
Matt
Drying time
30 min
Application method
Roller
Compliance
IRC 35
Rapide Water Based Traffic Marking Paint. Features: An extremely fast dry, durable 100% acrylic water borne paint. Complying with US Federal TT-P-1952 standards. Suitable for glass beads retention for retro reflectivity.
