Road Marking Hot Applied Thermoplastic Paint

Product Details:

Direction for use:

• Heat the material to 180 - 200 °C in the pre-heater with adequate agitation till the material becomes a homogenized liquid. Ensure that the road surface is clean, free from dust and moisture. Heavy deposits of paints requires removal. For aged asphalt roads and concrete road's application of a primer coat is recommended for proper bonding of the material with the road surface ensure that the primer is thoroughly dry and void of solvent prior to application of the thermoplastic material. Do not hold thermoplastic above 180ºC for more than 6 hours do not heat the material above 220ºC at any point in time. The change in colour indicates that the material has been scorched owing to overheating and needs to be discarded. Drop-on glass beads must be immediately deposited after thermoplastic application.

 

Safety Information:

• Minimise dusting of the material during use of personal protective equipment's like facemask, google, heat resistant gloves and protective clothing while handling the material is recommended. do not inhale product or fumes, do not ingest. avoid eye contact, if contacted, wash copiously with water. contact of the molten product with skin would lead to thermal burns, flush with cold water, do not remove material as it would lead to very tissue damage. Please refer the material safety data sheet prior to using the product.

Product Details:

Glass beads for road marking can improve the retro-reflection property of the road marking of the line. The driving at night, the headlights shines on the road marking line with glass beads, the light of headlights is reflected back parallelly. So, the driver can see the road ahead clearly, and drive safely at night.

Other Details:

• Protects from Moisture and Water
• Use no hooks

Product Details:

Direction for use:

• Heat the material to 180 - 200 °C in the pre-heater with adequate agitation till the material becomes a homogenized liquid. Ensure that the road surface is clean, free from dust and moisture. Heavy deposits of paints requires removal. For aged asphalt roads and concrete road's application of a primer coat is recommended for proper bonding of the material with the road surface ensure that the primer is thoroughly dry and void of solvent prior to application of the thermoplastic material. Do not hold thermoplastic above 180ºC for more than 6 hours do not heat the material above 220ºC at any point in time. The change in colour indicates that the material has been scorched owing to overheating and needs to be discarded. Drop-on glass beads must be immediately deposited after thermoplastic application.

 

Safety Information:

• Minimise dusting of the material during use of personal protective equipment's like facemask, google, heat resistant gloves and protective clothing while handling the material is recommended. do not inhale product or fumes, do not ingest. avoid eye contact, if contacted, wash copiously with water. contact of the molten product with skin would lead to thermal burns, flush with cold water, do not remove material as it would lead to very tissue damage. Please refer the material safety data sheet prior to using the product.

Additional Information:

• Production Capacity: 5000 MT
• Packaging Details: 25 KGS

Product Details:

Brightline Thermoplast Private Limited Hot melt Retro Reflective Thermoplastic Road Marking Paint. Thermoplastic is a long life road marking material that was first used in the USA in 1958, followed quickly by its introduction into many countries throughout Europe. It is a mixture of glass beads, binder, pigment and filler material. Thermoplastic can be used very effectively for large anti-skid areas on roads and pedestrian walkways by adding glass beads. It can be produced in any colour and is suitable for car parks, factory walkways, and many other areas. It hardens quickly and can be driven over after just a few minutes. Thermoplastics typically have a service life of 3-5 years, depending on conditions. In winter climates, thermoplastics are very susceptible to snow plows due to its raised structure and can be sheared completely off, leaving no marking on the road. It’s highly adhesive. ... It’s fast drying. ... It’s heat-stable and color-resistant. ... It offers increased resistance to road wear and tear and tropical climate conditions. ... It is the ideal kind of paint for reflectorized traffic paint applications. Thermoplastic road markings vary in thickness between 1.5 mm and 3 mm.

Additional Information:

• Production Capacity: 5000MT
• Packaging Details: 25 KGS

Product Details:

Brightline Thermoplast Private Limited Hot melt Retro Reflective Thermoplastic Road Marking Paint. Thermoplastic is a long life road marking material that was first used in the USA in 1958, followed quickly by its introduction into many countries throughout Europe. It is a mixture of glass beads, binder, pigment and filler material. Thermoplastic can be used very effectively for large anti-skid areas on roads and pedestrian walkways by adding glass beads. It can be produced in any colour and is suitable for car parks, factory walkways, and many other areas. It hardens quickly and can be driven over after just a few minutes. Thermoplastics typically have a service life of 3-5 years, depending on conditions. In winter climates, thermoplastics are very susceptible to snow plows due to its raised structure and can be sheared completely off, leaving no marking on the road. It's highly adhesive. ... It's fast drying. ... It's heat-stable and color-resistant. ... It offers increased resistance to road wear and tear and tropical climate conditions. ... It is the ideal kind of paint for reflectorized traffic paint applications. Thermoplastic road markings vary in thickness between 1.5 mm and 3 mm.